Produkty dla do silników (267)

Armaglass Connector L Preformed GFRP connector with improved adhesion surface, with "L" shape, 10 cm short side and long side available in different lengths, from 15 to 100 cm. Armaglass Connector L is used to mechanically connect ARMAGLASS networks to various supports (brick walls, stone walls, concrete, wood). The connector is perfectly compatible with the most common materials used for grouting, both resinous (epoxy, polyester, vinylester) and with mortars and grouts based on aerial or hydraulic binders. Armaglass Connector L is used to mechanically connect our ARMAGLASS networks to various supports (brick walls, stone walls, concrete, wood). It is an extremely durable connector, even when applied on alkaline supports, with high salt loads or when exposed to severe exposure environments. It is extremely easy to handle, light and easy to apply, which allows for rapid intervention and low installation costs. The improved adhesion allows optimal adhesions with resinous grouting matrices and with all the materials typical of ancient and modern masonry (brick, stone, mortar, concrete). Armaglass Connector L is part of the RINFOR SYSTEM 5 CRM reinforced plastering system, certified according to European evaluation EAD 340392-00-0104. Mechanical collaboration and connection of ARMAGLASS networks with supports. Reinforced plastering (CRM) interventions, even with high thickness, both on one side and on both sides of the masonry. Reinforcement of masonry arches and vaults. Reinforcement interventions on concrete structures. Particularly suitable for ancient walls of historical and cultural interest. Restoration and reinforcement interventions on buildings exposed to marine aerosol and offshore structures. Restoration and reinforcement interventions of water pipes, tanks, purifiers, piezometric towers, industrial water treatment tanks and in all structures that may be affected by the presence of aggressive soluble salts (chlorides, sulphates, nitrates, phosphates). Packaging: bulk - φ 8x70 mm Unit: €/piece

Most industrial process temperature control units work through the pressure exerted on the water of the process utilities: this is convenient in most “standard” cases, given the higher efficiency developed by the system. However, some critical process issues can make this type of operation difficult: this is the case of machines that leak fluids, or with leakage, and that it is not convenient to maintain on the spot. In such cases, it is therefore useful to work with a vacuum temperature control unit, which sucks in utility water. FTT PD water thermoregulators are flexible and effective systems, which can work under either pressure or vacuum depending on the peculiarities of the system. Any fluid losses are therefore minimized during operations. A simplicity of operation is also ensured by the touch-screen panel, also found on other Frigofluid temperature controllers. Models with an increased pump are also available for users characterized by high pressure drops. Temperature Range:up to 90°C

Consilex Nanosil T-1000 An impregnating water-oil repellent that is colourless, non-film and based on the nano-dispersion of silicon compounds. Protects lime-based plasters, cement mortars, concrete, natural stones, bricks, wood and so on from the weather, frost and thaw cycles, and aggressive atmospheric conditions. It does not alter the colour of the support nor impact the original appearance or breathability. Product characterized by a very high pearling effect (lotus flower effect) and excellent durability. Consilex Nanosil T-1000 belongs to the new generation of water-soluble fluorinated silica compounds, characterised by zero emissions of VOCs and the absence of flammability and toxicity. The active substance penetrates the porosity and micro-lesions, adhering to the support and counteracting the penetration and advancement of liquids without blocking the breathability of the support. The special chemical structure of Consilex Nanosil T-1000 ensures its high stability to alkali and thus its durability over time on various types of supports, such as: lime-based plasters, cement mortars, concrete, brick, natural stone and wood. The product differs from other treatments on the market due to having the following characteristics: - non-flammable - non-film - zero VOC - stable in water - free from emulsifiers - environmentally-friendly The treatment of absorbent materials carried out with Consilex Nanosil T-1000 is characterised by: - durability over time - total transparency - no variations to the surface colour - excellent water vapour breathability - elevated pearl effect - resistance to acids and alkalis - resistance to UV rays - an absence of reactive by-products that are harmful to people and the environment An impregnating treatment that is water-oil repellent, non-film, totally transparent and colourless, for above-ground masonry in brick, marble, slate, limestone, natural stone and tuff, cement or brick flooring, lime- or cement-based plasters and mortars, etcetera. Packaging: 25 kg canister UM: €/kg

Deterg-A Concentrated solution of buffered acids, anionic and non-ionic surfactants with high biodegradability, for deep cleaning of substrates from various kinds of encrustations (lime, gypsum, calcareous concretions, saltpetre). To be applied after diluting with clean water according to the proportions indicated in the technical data sheet. The product attacks carbonate minerals, therefore pay particular attention to surfaces in marble, limestone, floors and lead polished stones, carrying out appropriate preventive assessments. Protect metal surfaces Operations of saline removal and stabilisation, removal of deposits of lime, gypsum, saltpetre, mosses; deep cleaning of leakages and media in general. Particularly suitable as a detergent in waterproofing interventions with Protech Balcony. Dilute the product in water based on the nature and size of the incrustation and/or of salt fouling to be removed. Spread the solution with a spray or brush, or even by pouring directly on the fouling to be removed. Leave on for a few minutes. Wash the foam produced by the acid reaction with copious amounts of water . Deterg-A can be used in various dilution ratios: from pure (undiluted) up to one part of product in 10 parts of water. In preparation of the supports to be waterproofed with Protech Balcony, consider diluting the product 1:4, for a consumption of 400 g/m² of solution. In this case, the consumption of Deterg-A is about 1 litre of product to dilute per 10 sqm of tiled surface to be waterproofed. Do not apply on marble surfaces, terracotta, natural stone, polished lead floors and galvanised surfaces. It is a corrosive product, pay attention to the security fact sheet. Always wear gloves when handling. Packaging: 6 kg can UM: €/kg

Prerit Surface An impregnating water-oil repellent that is colourless, non-film and based on the nano-dispersion of silicon compounds. Protects washed gravel floors from the weather, frost and thaw cycles, and aggressive atmospheric conditions. It does not alter the colour of the support nor impact the original appearance or breathability. Also to be used, as a stain prevention during the washing operations of the surface to be deactivated, on the artifacts around the architectural flooring. Prerit Surface belongs to the new generation of water-soluble fluorinated silica compounds, characterised by zero emissions of VOCs and the absence of flammability and toxicity. The active substance penetrates the porosity, adhering to the support and counteracting the penetration and advancement of liquids without blocking the breathability of the support. The special chemical structure of Prerit Surface ensures its high stability to alkali and thus its durability over time. The product differs from other treatments on the market due to having the following characteristics: - non-flammable - non-film - zero VOC - stable in water - free from emulsifiers - environmentally-friendly - durability over time - total transparency - no variations to the surface colour - excellent water vapour breathability - elevated pearl effect - resistance to acids and alkalis - resistance to UV rays - an absence of reactive by-products that are harmful to people and the environment impregnating, hydro-oil repellent, non-film, totally transparent, colorless treatment of FLOORTECH PRERIT washed gravel architectural floors. Packaging: 5 kg can UM: €/kg

Armaglass Connector Twin Alkali-resistant fibreglass connector with rigid pre-formed central segment and double-threaded ends. Suitable for the structural reinforcement of brickwork, arches and vaults in masonry, tuff and stone, in combination with ARMAGLASS STRUCTURA fibreglass mesh and mortars such as Unisan, Intosana and the REPAR family. It is used as a conduit for connecting the two sides of structural plaster (with the “structural sandwich” technique). Armaglass Connector Twin is mainly used in plastering reinforced with sandwich systems comprised of mortars and fibreglass mesh. The rigid central section is available in segments of different lengths (200, 300, 400, 500 or 600 mm), while the two threaded ends are fixed at 200 mm in length. The ends are thus able to be opened radially and form an anchorage area of 400 mm in diameter. This method of connecting the two sides of the structural sandwich requires low-invasive preparatory operations, being easy to carry out and consequently resulting in low installation costs. The Armaglass Connector Twin is used to reinforce masonry, arches and vaults in brick, tuff and stone. It is used as a through-connection for joining two sides of a structural plastering . Packaging: bulk - 20x20x20 Unit of Measure: €/piece

Fluid Spritz Solution of mineral reactives (sodium silicate) to be used for the acceleration of setting of sprayed masonry and projected concretes, in the reinforcement of rocks outdoors and/or in a gallery, in laying self-sustaining and waterproofing claddings of tunnels, channels, vaults, basins, underground structures, etc., for use with specific equipment for hydrated mixtures (mixtures in which the silicate is sprayed on the shotcrete output nozzle). Fluid Spritz is a wide diffusion accelerant characterised by ease of use, dosage variability according to the specific construction needs: reduction in the number of coating layers to be applied, reduction of patch layer laying time, reduction of rebound swarfs, option to operate even in cold weather. Production of mortars and grouts sprayed with specific equipment (pumps for shotcrete machines) for hydrated mixtures in the reinforcement of rocks outdoors and/or in a gallery, in laying claddings, also with a load-bearing function, in galleries, on piles, sheet piles, diaphragms, channels, vaults, pondage, etc. In waterproofing underground structures. It can be used in structural sheets, for the safety of buildings affected by earthquakes. Fluid Spritz must be previously introduced into a tank of suitable capacity to be added directly to the spray nozzle. It is always advisable to carry out preliminary tests to determine the most appropriate percentage product addition. Packaging: 1350 kg tank UM: €/kg

Floor Tenax is a pourable, plastic/fluid, fibre-reinforced mortar for use in repairing deteriorated concrete flooring (with a reconstruction thickness from 4 mm to 20 mm) along with structural repairs of reinforced concrete cast in formwork. The formulation contains very fine yet high-strength cements, microsilica compounds with pozzolanic activity, rational granular aggregate composition curve (0.1–1.8 mm), special additives and a substantial amount of READYMESH fibre reinforcement. The product mixes with very low water/binder ratios (<0.32). The special formulation of Floor Tenax confers mechanical strength, fracture energy, exceptional durability and very high chemical-physical resistance to the repairs performed. Packaging: 25 kg bag UM: €/kg

Grout 6 SFR Grout 6 SFR is a high-performance, self-levelling castable mortar, reinforced with Readymesh MM-150 steel fibres and 6 mm Readymesh PM-060 polypropylene microfibres. It boasts high flexural strength, excellent adhesion to concrete and steel, and shrinkage compensation. The aggregates have a maximum size of 6 mm. It is ideal for anchoring road joints, restorations, reinforcements, and seismic adjustments, providing ductility for medium-to-high thicknesses (5–20 cm) on structures made of reinforced concrete and masonry. Structural restoration and adjustments, recovery and anchoring of road, motorway, airport joints, and critical area joints in general. Application surfaces should be clean, free of dirt, crumbling and non-adhering parts, dust, etc., and adequately saturated with water until they reach the condition "saturated with dry surface". Proper roughening of the surfaces through scarifying, sandblasting, etc., is always necessary to achieve maximum adhesion values to the substrate. Optimal values are obtained with high-pressure hydro-scarification. Remove any exposed rebar that is undergoing disruptive oxidation or is deeply oxidized, cleaning the rust from the exposed rebar (by sandblasting or using abrasive brushes). Pour about 2/3 of the mixing water into the mixer, add Grout 6 SFR and the remaining water; continue mixing until a homogeneous, lump-free mixture is achieved. The mixing water should be about 13%-15% by weight (3.5-4.5 litres per bag). Use casting procedures that ensure the absence of discontinuities and avoid the formation of air pockets. For high anchoring sections, it is advisable to add Ghiaietto 6.10 (please refer to the appropriate technical data sheet for more information). Packaging: 25 kg bag Unit of Measure: €/kg

Protech Sil P Therm white Anti-condensation, elastic, sanitizing, heat-reflecting paint, with hollow glass microspheres (3M Glass Bubble), ideal for both external and internal facades, based on siloxane resin in emulsion, with high permeability to water vapor and with excellent covering power. Recommended as a breathable, water-repellent protective finish for macroporous dehumidifying plasters (Sanatigh, Sanawarme, Caleosana). Protech Sil P - Therm is a paint suitable for any type of mineral substrate, such as old and new plasters, synthetic plasters, sandstone walls, etc. For old emulsion paints, remove non-adherent parts, remove any impurities, repair any cracks or crevices and then consolidate everything with Protech Fix AC - Therm, a silicon water repellent fixative primer, also suitable for highly alkaline substrates. Protech Sil P - Therm has excellent covering power: class 1 according to EN 13300 for a yield of 6/7 m2/l. In addition to the painting of external facades and internal environments, Protech Sil P-THERM has been designed especially for buildings and monuments subject to the protection of the ministry of cultural heritage. The binder based on an emulsion of silicones has allowed to develop a microporous filter impermeable to heavy rain, and at the same time permeable to the diffusion of water vapour. The great advantage of this paint is that it can be applied both on mineral (inorganic) supports and on previously treated supports with emulsion-based paints, creating a physical adhesion, with extremely microporous films. The particular chemical structure of the silicone binder produces a film resistant to light and atmospheric agents that is not destroyed even by microorganisms. For old emulsion paints, remove non-adherent parts, remove any impurities, repair any cracks or crevices and then consolidate everything with Protech Fix AC - Therm, a silicon water repellent fixative primer, also suitable for highly alkaline substrates. SUPPORTS ALREADY PAINTED WITH SILICATE PAINT Remove any stains and proceed with painting with the siloxane paint. (it is always recommended to apply a coat of siloxane impregnating agent). NEW SUPPORTS Apply a coat of siloxane acrylic fixative diluted from 20 to 60% with water depending on the absorption of the support. OLD SUPPORTS On old supports, remove the old paint by brushing, fill in any holes or imperfections in the wall with a suitable filler, proceed with fixing with siloxane impregnating agent diluted 20 to 60% with water depending on the absorption of the support. On large surfaces, it is recommended to apply the product of the same lot and proceed always wet on wet to avoid signs of resumption. Never operate at temperatures below + 5°C. Rainy weather, excessive atmospheric humidity and temperatures below + 8°C, can considerably compromise drying with the possibility of rainwater washout even after several days. In these situations, it is advisable to protect the facades from unpredictable showers, in order not to jeopardize the success of the work. For storage store in tightly closed containers and protect from frost. Packaging: 4-liter bucket UM:€/l

Consilex Inject Mauer One-component silane-based system modified for the preparation, with the sole addition of water, of water repellent microemulsions for slowly spreading masonry injections against capillary rising damp or using a pump with low operating pressure (0.5 to 1.5 bar), specific for the construction of chemical barriers in masonry, brick, tufa, stone and mixed, of varied thicknesses. The injection of Consilex Inject Mauer can be made using a pump with low operating pressure (0.5 to 1.5 bar) or else via drop-down and slow diffusion using special graduated bags (Barrier Bag) and injection tubes (Barrier Tube D26). The slow diffusion, carried out with the accessories mentioned above is specifically designed to facilitate the deep and complete interpenetration of the formulation into the porosity of the material, even without mechanised pumping systems being set up. Being deprived of its source of damp, the masonry above the operation will gradually and slowly yield its residual moisture content by evaporation. Since this process can crystallise the salts contained in the masonry, bleaching and saline efflorescence effects may occur on the surface of the exposed masonry or plaster with accentuated phenomena of superficial degradation. Thus, for plastered masonry that has become compromised, completing a cycle of dehumidifying plastering is recommended, using Untersana, Sanatigh or Sanastof for example. For exposed masonry, it is recommended to allow the salts to vent throughout the summer period and then, if necessary, complete the operation with a water-based surface water repellent treatment such as Consilex Altrain WV. Construction of slow diffusion chemical barriers or using a pump with low operating pressure (0.5 to 1.5 bar) against capillary rising damp in brickwork, tufa, stone and mixed, of varying thickness. In the event that injection is performed with pumping systems, the hole usually has a diameter of 12 mm, being able to accommodate the rubber and steel injector. If the injection is carried out by slow diffusion, the drill bit must be 30 mm to permit the insertion and housing of the Barrier Tube D26 cardboard tubes, connected externally via the specific polyethylene Barrier BagS and their tubes, as better described in the product data sheets. Pour the prepared mixture into the mechanised pumping system or fill the previously-prepared containment Barrier BagS until the quantity of the necessary mixture has been completely absorbed. In normal absorption conditions, masonry with a thickness of about 40 centimetres will soak up about 16 litres of the 1:10 solution for each metre in length. Once fully absorbed: - if using pumping systems, remove the injectors and putty the holes; - if using the drop-down system, remove the bags and tubes installed, leaving the cartridges “to be lost” in the holes, which will then need to be properly filled completely and puttied on the surface with cement- and/or lime-based mortar. Packaging: 10-liter can UM:€/l

Osmocem SCK Fiber-reinforced monocomponent cement mortar, based on hydraulic binders, superprogoline fillers, selected fine aggregates and crystallizing reagent agents, which favor the penetration of the compound into the support. Ideal for low-thickness protective coatings (4 to 10 mm), with high counterweight adhesion. The specific formulation makes this product ideal for coatings in aggressive environments in contact with chlorides and sulphates (sewage systems). Packaging: 25 kg bag UM: €/kg

Protech Fix AC-Therm Water-based anti-condensing wall covering, with excellent fixing and anchoring properties, with good coverage based on high penetration acrylic resins, 3M Glass Bubble, pigments, fillers and covering fillers. Suitable as an anti-condensation fixative primer, prior to painting or coating the plaster with anti-condensation paints or plasters (-THERM). Ideal for interventions on walls with mucilage deposits, bacterial phenomena and moulds. Due to its low thermal conductivity, it is particularly suitable for solving mould problems. It can be applied on any plaster (rustic, civil, plaster, dry mortar, plasterboard, concrete, prefabricated, exposed concrete, etc.). Made with special resins and additives it reduces the absorption of the support while allowing the necessary transpiration, uniforms the absorption making the application of the finishing coats easier. It always works in depth, which is why it is the ideal preparation for applying water-based paints or coatings. Adhesion is excellent even on particularly difficult surfaces, thanks to the use of special resins and the presence in the formulation of an adhesion promoter interacting between the support and the product. Preliminary treatment of any surface (civil, plaster, rustic, dry mortars, plasterboard, concrete, prefabricated, exposed concrete etc.) designed to isolate the support surfaces and standardise the absorptions of the subsequent anti-condensate treatments (painting and protective coatings). Packaging: 14-liter bucket UM: €/l

Filtene Fondogiunto Closed cell polyethylene foam kerb, compressible, to properly size the depth of the expansion joints (creation of the "third wall" or base material) before filling them with the polymeric sealants Protech Flex, PROTECH SIGILFLEX MONO or EG 91. It is available in profiles of circular cross-section of different diameter that will fit joints of any shape and size. Suitable for any type of joint between prefabricated elements, infills, bodies of different structures, partitions, doors and window frames, flooring. The insertion of a "joint base" filler material has many functions in both static and expansion joints: sizing the joint in the most appropriate shape and measurements for the characteristics of the sealant to be used, reducing the stresses internal to the sealant itself and on the adhesion to the walls; favouring the contact of the sealant with the side walls during joint filling; reducing sealant consumption. Filling the "joint base" for any type of joint between prefabricated elements, infills, bodies of different structures, partitions, doors and window frames, flooring, prior to laying the elastic sealant in the joint itself. The diameter of Filtene Fondogiunto should be about 25% greater than the width of the joint to allow a stable positioning of the profile and create sufficient resistance to the pressure exerted by the sealant during extrusion. Push with a tool with a rounded tip (free of sharp and pointy edges), capable of crossing the width of the joint, Filtene Fondogiunto, up to the desired depth and so as to leave on the surface an adequately deep seat for the subsequent sealant. Normally the depth of the sealing should be about half the width of the joint. Polyethylene foam is unaffected by solvents contained in the primers, but it is a good idea never to apply the adhesion promoter Protech Flex Primer on Filtene Fondogiunto, in order not to alter the anti-adherence properties. FILTENE can then be inserted into the joint after applying the primer, when the "dust-free time" is attained. A good rule is for the depth of the sealing (adjustable depending on the positioning of Filtene Fondogiunto) not to exceed the width of the joint itself. Confezione: Rotolo da 25 metri UM: €/m

Fluid SRA Concentrated liquid additive formulated to reduce shrinkage in the plastic phases of cement mortar. It reduces shrinkage by over 50% compared to the same mixture without the additive, especially when curing conditions are not possible in a humid environment. Excellent in combination with anti-shrinkage and structural fibers for achieving high structural performance works. It can be used in certain thixotropic and castable structural mortars of the REPAR and GROUT families according to the quantities specified in the respective technical data sheets. For mortars with high volumetric stability. Reduces cracking caused by shrinkage in the plastic phases of cement mortar. Reduction of free air shrinkage in some structural mortars of the REPAR and GROUT families (particularly useful when wet curing conditions for structural mortars are not feasible). Fluid SRA must be added to the mortar after adding the mixing water to the cement mixer. After addition, mix thoroughly before casting. The typical dosage for normal use is approximately 1% relative to the weight of the binders. Packaging: 1 kg bottle UM: €/kg

Consilex ST Transparent penetrating consolidator, for natural stones, ornamental stone elements, mineral plasters and in general for the restoration of cultural heritage. It consists of ethyl esters of silicic acid in solvent, hardening by reaction with atmospheric humidity. It is applied by spraying at low pressure, until the treated surfaces are rejected, in order to guarantee an extremely deep consolidation. Packaging: 5-liter can UM: €/l

Floor Level Floor Level is a self-levelling modified-polymer cement mortar with fibre-reinforcement, offering accelerated grip and fast hardening. Applied prior to laying the flooring, it is perfect for levelling at thickness ranging from 3 mm to 20 mm so as to adapt to any type of covering. Floor Level is a self-levelling modified-polymer cement mortar with fibre-reinforcement, offering accelerated grip and fast hardening. Applied prior to laying the flooring, it is perfect for levelling at thickness ranging from 3 mm to 20 mm so as to adapt to any type of covering. Floor Level is a self-levelling modified-polymer cement mortar with fibre-reinforcement, offering accelerated grip and fast hardening. Applied prior to laying the flooring, it is perfect for levelling at thickness ranging from 3 mm to 20 mm so as to adapt to any type of covering. Packaging: 25 kg bag UM: €/kg

Protech Balcony Solution based on special silane and siloxane resins in solvent, highly penetrating, transparent (colourless), for quickly, effectively and economically waterproofing balconies, tiled terraces, concrete roofings, external stairs, etc., without removing or intervening on the existing flooring. It does not change the appearance of the support on which it is applied and it does not alter the original slipperiness or its water vapour breathability. It is quick to apply and does not require skilled labour or professional equipment. The flooring treated will be usable after only 2 hours of laying. Protech Balcony is a product that is easy and quick to apply: simply spread it out with a scrubbing brush on clean and dry surfaces to solve the problem of infiltration. The active ingredient, effectively conveyed in a solvent, it penetrates fillings, substrate cracks and porosity rapidly and in-depth. Upon contact with air, it performs a polymerisation reaction that seals and waterproofs, perfectly and in depth, all discontinuities where it has managed to penetrate. After the reaction, the specific polymerised siloxane molecule is stable over time and does not labilise. Thus, the effective life of the product being applied on surfaces which are not subject to dynamic movements and seismic activity, is normally in excess of 10 years. If necessary, if new discontinuities, cracklings, cracks, fissures etc. appear after the first application of Protech Balcony, these may conveniently be resolved with a second application of the product. Given its intrinsically non-pellicular nature, the product will not be subject to fissures, tears, cracks, separations, deterioration and will not yellow over time, under the effects of UV rays (as occurs naturally for epoxy and/or polyurethane treatments). The surfacings treated with Protech Balcony will be resistant to mildew, moss, lichens and other biodeteriogenic bodies. Please note that the effectiveness in terms of water repellence, and watertightness of Protech Balcony has been certified with suitable tests conducted at the laboratories of the department of structural engineering of POLITECNICO DI MILANO (the Polytechnic of Milan). Quick waterproofing, of balconies, terraces, stairs, decks, tiled surfaces, concrete structures, and natural stones, without demolishing the existing flooring. Also for use on vertical surfaces particularly exposed to the inclemency of the weather and atmospheric agents (tiled, plastered, exposed brickwork, etc.). The application surfaces should be clean, free of incrustations, crumbling and non-adhering parts, dust etc. The vanishing points between tiles, if present, should be appropriately treated with suitable acid or alkali cleaners. In this respect it is recommended that the specific acid detergent Deterg-A, diluted with water at a ratio of 1:4. Rinse the treated surfaces with running water. Labile and non-adhering vanishing points, possibly removed, are required to be restored with high adhesion and deformability cement surfacers. In this respect it is advisable to use of the specific two-component waterproof and deformable filler Stucco Balcony. Wait for the necessary time (1-2 days) for drying the filling before applying Protech Balcony. Any expansion joints present, including those relating to the junction line of the tiled flooring and the perimeter kerb (typically made of granite or natural stone), will have to be sealed with high elasticity polymeric materials. In this respect, it is advisable to seal them with Protech Flex, assisted by laying Filtene Fondogiunto and the appropriate polyurethane primer Protech Flex Primer. Pour small amounts of product at a time and spread it evenly over the entire surface with a scrubbing brush or a "water squeegee", until complete impregnation of the support to be waterproofed. Set Protech Balcony with all due care in less accessible and more uncomfortable areas, by using a brush with long bristles or a sponge (edges, skirting boards, corners, sills, wells, chimney flues, discharges, etc.). Allow the product to penetrate for at least 60 minutes. Within maximum 120 minutes of application, remove the excess product on all surfaces treated with a cloth soaked in the diluent Nitro. The product consumption is on average about 0,125 l/m² of surface to be waterproofed; varying according to the absorption of the support and the size of any vanishing points. Normally it is considered that with 1 litre of Protech Balcony you can treat from 7 to 15 m² of surfaces. Packaging: 2-liter can UM: €/l

Fluid Therm Multi-purpose Additive solution specific for the improvement of thermal conductivity of concretes, through balanced superlubricating, defoamer, plasticiser type actions. Fluid Therm is perfectly compatible in combination with steel Readymesh MM-150 (usually dosed at 25 kg/m³) or multifilament Readymesh PM-180 (usually dosed at 1 kg/m³) polypropylene fibres In radiant panel heating systems , the presence of high air content in the concrete forming the levelling screed can cause the correct spread of thermal energy to be severely obstructed; on the other hand, the conglomerate incorporates air already in the mixing phase in the form of microbubbles, while the excess mixing water and the segregation mechanisms that occur during transport and casting contribute to including additional quantities of air in the form of macrobubbles in the conglomerate. In this context, the peculiar defoamer, superlubricating and antisegregative actions of Fluid Therm, are particularly valuable as they allow the production of grouts and concretes with very low air content. Packaging: 10 kg canister UM: €/kg

Syntech Roadware Syntech Roadware is a high penetration two-component hybrid urethane which, combined with quartz, produces a hard and instant polymer to repair cracks and crevices in concrete floors. Syntech Roadware has a very low viscosity allowing the penetration of the product in depth, even in the narrowest cracks. It has short reaction times, in fact in 10 minutes at 20°C the material polymerizes completely and catalyzes quickly even in environments with temperatures below 0°C. It has good resistance to chemical attack. When combined with quartz powder, Syntech Roadware, forms a highly resistant compound with properties similar to existing concrete but with the flexibility that persists over time. Repair of splits or cracks in concrete, restoration of deteriorated concrete degradation, repair of cracks and pop-out phenomena in concrete. Slightly widen the crack with a circular saw to facilitate the penetration of Syntech Roadware. Before applying the product, vacuum the dust created. The support must be clean and free from dust or dirt. Apply Syntech Roadware directly on the crack or on the degraded area until the gap is completely saturated. Add quartz directly to the crack and repeat the Syntech Roadware application operation. Smooth with a spatula and leave the product to work. With a Syntech Roadware cartridge, an average of 50 linear metres of gap of 5 mm width is repaired. Bi-mix cartridge 600 ml

Syntech Pavisheer A two-component epoxy system based on epoxy resins in aqueous dispersion and solvent-free. It is ideal for completing protective, transparent treatments with a consolidating action and anti-dust effect on industrial concrete flooring, with good mechanical and chemical resistance, especially in reference to contact with oils and solvents. This product also serves well as a primer for casting joints between old and new concrete flooring. Transparent finish of interior floor coverings, mechanical-resistant impregnations, anti-dust and anti-oil for concrete surfaces. The media should have adequate mechanical resistance. The concrete surfaces should be cured, dry, planar and absorbent, free from oils, detergents, powders and soiling. The most appropriate type of mechanical preparation should also be determined (degreasing or shot peening). Conveniently absorbent surfaces may be dealt with directly after a proper cleaning. For tiled surfaces and for pre-existing coverings in resin, a degreasing or shot peening treatment is required until complete opacification and complete elimination of dust. Mix components A and B each in their own container before mixing. Do not take partial quantities from the packs to avoid any errors in the mixing ratio that would cause failure or incomplete hardening. Pour component B into a suitable container and add component A. Mix everything for a few minutes using a mechanical stirrer with variable speed until a homogeneous and uniform color mixture is obtained. Leave to rest for a few minutes and mix again. Dilute the final product only with water in the Syntech Pavisheer: water ratio of 1: 3 for the first coat and 1: 2 for the second. Gradually add the dilution water, continuing to mix for a few minutes. The dilution ratio can vary according to the porosity of the support; if necessary on closed surfaces it is also possible to dilute the second coat respecting the dilution ratio 1: 3. The Syntech Pavisheer emulsion has a stability of about 2 hours at 20 ° C; within this period the product must be used. Syntech Pavisheer is applied with a short-haired roller or spray, covering the entire surface evenly. We recommend application at temperatures not lower than 5 ° C. From 0.10 to 0.15 kg of SYNTYECH PAVISHEER for each square metre of surface to be covered. Can 5 kg [A] - Canister 1 kg [A] - Can 5 kg [B] - Canister 1 kg [B] - Kit: 1 Canister 1 kg [A] + 1 Canister 1 kg [B] - Kit: 1 Can 5 kg [A] + 1 Can 5 kg [B]

Syntech Pavidamp A three-component formulation, with a fluid epoxy resin base in aqueous emulsion (A + B) to be mixed with the third component (C) consisting of white cement and micro-quartz, specially designed to be used as a primer for cementitious surfaces in the presence of humidity and in conditions of hydraulic counter-thrust. Generally referred to as “wet-bonding”, it is particularly suitable as an anti-humidity barrier for the subsequent laying of parquet. Building connection layers and smoothing cement surfaces; bottom layers for resinous coatings of floorings in the presence of damp subbases; anti-humidity barriers in concrete, brick and stone masonry; surfacings of porosity, cracks and superficial irregularities. As protection from rising damp for bases where operations with polyurea resins SYNTECH POLYUREA will be carried out. The support on which the resin system is to be laid must be suitable for withstanding the stresses resulting from the intended use, such as static or dynamic loads, impacts, thermo-hygrometric dilatations, vibrations, etc. As regards the characteristics of the substrate (maximum humidity, cohesion, strength class, flatness, etc.) and the preparation of the surface that will accommodate the resin system, we recommend the requirements set out in chapter 5 of the UNI 10966 standard ("RESIN SYSTEMS FOR SURFACES HORIZONTAL AND VERTICAL - INSTRUCTIONS FOR DESIGN AND APPLICATION "). In any case, carefully clean and degrease the surfaces, removing any kind of dirt, paint residues or incoherent parts. Evaluate the most convenient type of mechanical preparation (shot peening, sandblasting, hydro-washing, etc.). The surfaces must also be free from discontinuity, and possibly leveled and regularized with products from the FLOOR line or the REPAR line. Apply by roller, brush or spray from 150 to 200 g / m2 of Syntech Primer EP-W to consolidate the substrate and facilitate the adhesion of the subsequent coating. Tiled floors, or floors covered with pre-existing resin, must be subjected to mechanical roughening carried out with shot blasting, milling, bush hammering, etc., until the total elimination of the waterproof crust and the opacification of the surfaces. Remove dust after abrasion. Prepare the mixture of the 2 liquid components (A+B), pouring the contents of the component B in the container of the component A. Mix with drill for about 2 minutes. Add the pre-dosed hydraulic binder (high resistance white cement) to the mixture A+B, and mix with a mixer drill. To disperse the product optimally, pour the powders (component C) a little at a time, continuing to stir with drill, until a homogeneous lump-free mixture is obtained. If it is used as a base: dilute with 10-15% by weight of clean, soft water and apply with a roller or brush. Indicative consumption: 0.4-0.5 kg/m² on regular supports, 0.7-0.9 kg/m² on irregular supports. If it is used for fine finishing coats: load the system A+B+C diluted with 10-15% of fresh clean water, with 60-70% spheroidal quartz (0.04-0.25 mm). Apply with steel trowel or plastering trowel. Indicative consumption: 1-2 kg/m². If it is used for medium finishing coats: load the system A+B+C diluted with 10-15% of fresh clean water, with 70-80% spheroidal quartz (0.1-0.5 mm). Apply with steel trowel or plastering trowel. Indicative consumption: 3-4 kg/m². From 0.50 to 0.60 kg of SYNTYECH PAVIDAMP for each square metre of surface to be covered. Pail 3.8 kg [A] - Pail 1.2 kg [B] - Pail 5 kg [C] - Kit: 1 Pail 3.8 kg [A] + 1 Pail 1.2 kg [B] + 1 Pail 5 kg [C]

Syntech Pavicrom SBV Colored two-component finish, permeable to water vapour, based on epoxy resins in water dispersion. Ideal for the pigmented coating of industrial floors and concrete constructions in general with residual humidity and without vapor barrier. Surfaces treated with Syntech Pavicrom SBV are easy to clean and guarantee excellent resistance to mechanical wear, as well as being highly resistant to water, alkaline solutions, detergents and hydrocarbons (petroleum, diesel, petrol, etc.) . Protective and decorative painting of concrete floors, restoration of the color of old resin floors, glazing of wall skirting boards, etc. Ideal for mechanical workshops, manufacturing industries, warehouses and factories in general where high chemical and mechanical resistance is required. It can be used both indoors and outdoors. Concrete The surfaces to be coated must be stable, clean and free of substances that could affect the adhesion of the coating. In case of restoration, use suitable mortars and products suitable for the system beforehand. Wait for the drying times before applying the next coat. The tensile strength must not be less than 1.5 N/mm². Existing paints, coatings or paints, cement grout residues, release agents, oils, greases, silicones, etc. they can be removed mechanically by sandblasting, blasting, hydroblasting or chemical removal. Cracks and fissures In case of static cracks, use Syntech Primer EP-W for sealing. The sealing of dynamic cracks or cracks larger than 4-5 mm must be assessed on site. Generally they can be grouted with elastomeric materials or act as expansion joints. Grouting and spot repairs Any holes or repairs to portions of concrete can be made with mortars from the REPAR line or by applying epoxy mortar made with Syntech Primer EP-W and quartz mastics. Apply a coat of Syntech Primer EP-W as a bonding primer, then proceed to seal and repair the damaged and broken concrete by applying the epoxy mortar. Any small filling of holes and cracks can be done by applying Syntech AS 21 epoxy mortar. Resin coatings The surfaces to be covered must be stable, clean and free of substances such as dirt, grease, oil, etc. which can affect the adhesion of the coating. Smooth the surface by mechanical sanding with diamond discs and vacuum. It is recommended to wash the surfaces and let them dry completely before applying the finish. Primer for concrete Syntech Pavicrom SBV can be applied directly to cementitious substrates as the product diluted with a maximum of 25% by weight of clean water acts as an anchoring primer. Resin coatings The application of Syntech Pavicrom SBV on resinous and multilayer systems must always be preceded by sanding the entire surface to promote and guarantee optimal adhesion of the product to the support. Combine the two components in the indicated mixing ratio. Add component B (hardener) to component A (base) and mix well until a completely homogeneous product is obtained. It is advisable to start mixing briefly with an electric drill at low speed and then intensify the stirring up to a maximum of 300-400 rpm. Leave the emulsion obtained to rest in the container, respecting the following induction times: at 15°C ~ 20 minutes at 25°C ~ 15 minutes at 30°C ~ 10 minutes The product can be applied uniformly using a spray gun or short-haired roller to avoid accumulations of material which could give rise to aesthetic defects. The application of the product must be carried out by crossing the passes and paying particular attention to the shots, regularly unloading the roller beyond the applied area to obtain a uniform film and eliminate any accumulations of product. Apply the first coat of Syntech Pavicrom SBV diluted with a maximum of 25% by weight of clean water as primer. The dilution must be carried out under mechanical stirring, adding the necessary quantity of water at the end of the induction time. Do not dilute the product further during application if it thickens it means that the use time has expired. Create a new emulsion with highly mixed material. Wait at least 12 hours, then apply the second one Colored finish diluted with a maximum of 20% weight of clean water, respecting the consumption and thicknesses indicated. It is possible to create non-slip finishes by adding quartz or hollow glass spheres. From 0.15 to 0.20 kg of Syntech Pavicrom SBV for each square meter of surface to be covered, for each coat. Pail 2.5 kg [A] - Pail 5 kg [A] - Pail 3 kg [B] - Pail 6 kg [B] - Kit: 1 Pail 2.5 kg [A] + 1 Pail 3 kg [B] - Kit: 1 Pail 5 kg [A] + 1 Pail 6 kg [B]

Syntech Epox Level Two-component coloured, high solids, self-levelling and/or multi-layer epoxy coating on concrete surfaces and cementitious substrates. Excellent mechanical and abrasion resistance Wide range of colors available Uniform, glossy finish with possible non-slip finish Excellent mechanical and chemical resistance Excellent resistance to detergents and disinfectants. ▪ Colored abrasion resistant coating ▪ Coating of floors subjected to intense traffic ▪ Coating of floors in laboratories, hospitals, sterile rooms and aseptic rooms ▪ Flooring of warehouses, shopping centres, museums, showrooms, storage and logistics areas ▪ Coating of floors of underground car parks, garages, hangars, automotive and aeronautical industries ▪ Coating of food industry floors ▪ Coating of floors in chemical and pharmaceutical industries. Self-leveling coating SYNTECH EPOX LEVEL: 1 kg/m2 QUARTZ 0.1-0.5: 0.8 kg/m2 Multilayer system 1st layer SYNTECH EPOX LEVEL: 1 kg/m2 QUARTZ 0.1-0.5: 0.8 kg/m2 + 2-3 kg/m2 for waste sowing 2nd layer SYNTECH EPOX LEVEL: 0.5 kg/m2 QUARTZ 0.1-0.5: 0.2 kg/m2 + 2-3 kg/m2 for waste sowing Finish SYNTECH EPOX LEVEL: 0.3 kg/m2 QUARTZ 0.06-0.25: 0.05 kg/m2. Can 10 kg [A] - Can 2.3 kg [B] - Kit: 1 Can 10 kg [A] + 1 Can 2.3 kg [B]

Stucco Balcony A two-component, fine cementitious grout with a fluid plastic consistency for grouting uncovered joints or filling and finishing static cracks, micro- and macro-cavities and so on between flooring tiles, before applying Protech Balcony for breathable non-film waterproofing operations on terraces and balconies. Specific putty for the preliminary preparation of supports (open gaps, micro and macro-cavities and fissures) for the subsequent application of Protech Balcony on terraces and balconies. Application surfaces should be clean, free of soiling, crumbling and non-adhering parts, dust, etc., conveniently saturated with water until they reach the condition "saturated with dry surface". Add the quantity of component B required to obtain the desired consistency to component A; mix thoroughly until a homogeneous lump-free mixture is obtained. Place on site using a spatula, sponge float or simply with the fingers of the hand (wearing a rubber glove). it is possible to correct the consistency, where necessary, by adding moderate quantities of water to the ready mixture. In the cases of coloured surfacings, it is recommended to mix the two-component with small amounts of coloured pigments that can be purchased at any paint shop. Approximately 1.75 kg of Stucco Balcony for each cubic decimetre of volume to be grouted. Pail 4 kg [A] - Bucket 0.8 kg [A] - Bottle 1 kg [B] - Bucket 0.2 kg [B] - Kit: 1 Pail 4 kg [A] + 1 Bottle 1 kg [B] - Kit: 1 Bucket 0.8 kg [A] + 1 Bucket 0.2 kg [B]

Sealpvc SF 240 The SEALPVC SF 250 waterstop is a waterproof profile in PVC that is not hydro-expansive, having a thickness of 24 centimetres and high elasticity. It is used in static joints for horizontal casting (slabs), in concrete structures, resting on the substrate beneath the reinforcement. Given its particular composition, it can be cut with a sharp blade (cutter) and welded with simple heat welding tools, thus making it easier to create connections in the course of work. Waterproofing of static construction joints between: raft foundation and the elevation wall, between two raft foundations, between two elevation walls, between the wall and floor, resting on foundations under the shoring. Bind with iron wire the side flaps of the waterstop to the steel plates provided, in order to position it and secure it in a central position with respect to the casting to be made. Proceed with the casting operations, ensuring it does not bend nor move from the seat identified. 1 m/m: Use Sealpvc SF 240 welding the two edges of different belts head to head using a leister (manual hot air welder). Roll 25 m

Sealpvc RG 250 Bulb The Sealpvc RG 250 Bulb waterstop is a waterproofing PVC profile that is not hydro-expansive, having a thickness of 25 cm with a central and highly elastic bulb. It is used in dynamic joints for horizontal (slabs) or vertical (elevation walls) constructions, in concrete structures, in the central position of the cast. Given its particular composition, it can be cut with a sharp blade (cutter) and welded with simple heat welding tools, thus making it easier to create connections in the course of work. Waterproofing of the dynamic construction joints between: raft foundation and the elevation wall, between two raft foundations, between two elevation walls, between the wall and ceiling. Bind with iron wire the side flaps of the waterstop to the steel plates provided, in order to position it and secure it in a central position with respect to the casting to be made. Proceed with the casting operations, ensuring it does not bend nor move from the seat identified. 1 m/m: Use Sealpvc RG 250 Bulb welding the two edges of different belts head to head using a leister (manual hot air welder). Roll 25 m

Sanaxil I Natural, protective, decorative, breathable, pigmented, non-toxic, anti-mold plaster, with stabilized potassium silicates, for interiors and exteriors. Substantially mineral formulation which, thanks to the natural alkaline pH of potassium silicate, develops a strong antibacterial and anti-mold action. Sanaxil I is a versatile and valid product in various application fields: in green building interventions, in new constructions and in the restoration of period and monumental buildings. The product does not form a film, thus avoiding detachment and flaking phenomena and, while ensuring excellent water repellency, ensures high values of permeability to water vapor thanks to its porous and microcrystalline structure, perfectly compatible with mortars, plasters and all other common elements of the body masonry. Physical-mechanical performance and durability are coupled with a vast choice of colors that cannot be altered over time; characteristics which, combined with the ease and practicality of application, make the product extremely versatile and adaptable to any project requirement. Restoring protective coatings based on stabilised potassium silicates, for vertical and horizontal surfaces. Application surfaces should be clean, free of soiling, crumbling and non-adhering parts, dust, etc., conveniently saturated with water until they reach the condition "saturated with dry surface". Existing paints (washable, organic, solvent-based etc.) must be removed. Homogenise the surfaces by applying the fixative Sanaxil Fix. Spread SANAXIL in two coats: the first, for simple deposition, with steel trowel, the second, for spreading and finishing, with sponge float. The application of the second coat must be carried out, when the first coat starts to dry, under one of two suggested conditions: with dry trowel, for smooth surfaces; with moistened trowel, for antique-effect surfaces. Sanaxil I is dry to the touch after 4 hours, it can be overcoated after 2-5 hours, while it will be dry in-depth after 16-32 hours. Indicative consumption depending on the different particle sizes of Sanaxil I available: 1 mm GRAIN: approximately 1.25 -1.40 kg/m²; 1.2 mm GRAIN: approximately 1.40 -1.55 kg/m²; 2 mm GRAIN: approximately 1.85 -2.15 kg/m²; 2.2 mm GRAIN: approximately 2.00 -2.30 kg/m². The indicated yields refer to smooth supports and are for guidance only. Actual consumption must be identified with a suitable practical test. Pail 5 kg - Pail 25 kg

Sanaxil Fix Reinforcing, fixative, transparent primer, based on stabilised potassium silicate for the preliminary treatment of the surfaces to be painted and/or plastered with silicate-based, lime putty, systems, for ecological building interventions, new buildings and for the restoration of vintage buildings and monuments. Sanaxil Fix is a product consisting of potassium silicates. It is highly breathable and is not subject to thermoplastic effects. It does not contain resins, solvents, thinners and harmful or toxic emanations. Free of V.O.C. "Priming" fixative treatment of coatings, paints or putty coat based on lime putty, potassium silicate and siloxanes in general. Dust-proofing, reinforcing, cortical treatment for surfaces of pulverising plaster. Organic type paints (washable, solvent-based etc.) where present, must be thoroughly removed. The support should, in any case, be, clean, homogeneous, compact, dust-free. SANAXIL-FIX can be applied to substrates in masonry, on cement surfaces, lime-based surfaces, on well anchored mineral paints. They can be applied by brush, roller or spray: the number of coats required and the most appropriate dilution ratio with water will be determined as a function of the absorption conditions and degradation of the support. The admissible dilution range provides for additions of water up to a maximum ratio of 1:1. Apply from 0.10 to 0.15 litres of Sanaxil Fix per square metre of surface to be treated. Plastic can 5 l - Plastic can 20 l

Sanastof A premix with a composition of breathable minerals for dehumidifying, with a base of natural hydraulic lime NHL 3.5, microsilicas with pozzolanic activity, selected aggregates, high tenacity microfibres and inert light unit weight thermal-insulating aggregates with a low elastic modulus. It is used for skimming and smoothing, both indoors and outdoors. This product is perfectly compatible with multiple substrates: lime-based plasters, lime cement, cementitious mortars, concretes, porous stone and brick. Its characteristics render it particularly suited to green building works and for restoring historic and monumental constructions. The maximum grain size of the aggregate is 0.9 mm. Sanastof is a product based on natural hydraulic lime, kaolin, marble dust, selected siliceous aggregates and lightweight aggregates with low elastic modulus, dimensionally stable. It is a natural product with high intrinsic breathability and does not have traces of resins, solvents, thinners and radioemissive aggregates. The product contains high tenacity microfibres that give great volumetric stability. The special hollow, rounded, dimensionally stable, aggregates give the skimming special thermal insulation qualities, filtration of potentially harmful soluble salts and reduction of the elastic modulus. The granulometric curve, the finesse of the binders and some natural rheological additives, make the product particularly smooth in the application phase, even when laid on supports with rough or difficult surfaces. The calibrated physical-mechanical characteristics guarantee perfect compatibility on different types of support, especially on traditional plasters and mortars. The microsilicic content of pozzolanic activity makes the skimming and the levelling performed with Sanastof extremely durable, even in aggressive exposure environments. Quick and easy application on various supports, such as: breathable finishing for wall coverings; skimming on modular insulation made of wood fibre or calcium silicate; levelling of plastered surfaces; skimming of concrete surfaces; levelling and skimming of restorations carried out with cementitious mortars; application with mainly thin thicknesses (from 1 to 4 mm) with simultaneous levelling of recesses, imperfections etc. In particularly harsh work conditions it is advisable to position the Armaglass 160 alkali-resistant fibreglass reinforcing mesh between the first and second coat (the mesh must be partially embedded in the first coat of Sanastof when it is still fresh). The breathability, combined with the other physical-chemical characteristics of the product, make the skimming carried out with Sanastof an ideal support to accommodate any kind of painting and in particular the mineral paints based on potassium silicate or lime putty. Sanastof is the breathable, low elastic modulus finish, recommended in all our dehumidifying systems carried out with: Sanatigh, Caleosana, Sanawarme, Unisan, Intosana. Application surfaces should be clean, free of soiling, crumbling and non-adhering parts, dust, etc. Smooth supports should be roughed (roughness > = 1mm). If after cleaning and roughening the support is still dusty and crumbly, remove the parts completely inconsistent with spatula-brush, or by assisting the removal operation with a power wash, then consolidate the support by impregnation with Protech Fix AC aqueous emulsion applied in two abundant coats, the second coat immediately before applying Sanastof with the "fresh on fresh" technique (the consumption of Protech Fix AC for this priming operation is between 120 and 250 gr/m2). Adequately wet the support with water before application, anticipating and repeating this operation several times in case of very porous and absorbent supports or in the presence of warm and arid climates. Bag 25 kg - Pallet: 50 x (Bag 25 kg)